[email protected]
800-645-6733
Home About Us Line Card Careers Products Contact Us
[email protected] 800-645-6733
Home
About Us
Products
Line Card
Careers
Blog
Contact Us
Features
  • D500 Series features cap design
  • MD500 Series features cup design with manual override ring
  • Zero leakage from 0 psi up to 70% of the marked set pressure
Please specify ‘ASME’ when placing your order.
Unit of Measure

Specifications

Series

N/A D500

O-Ring Material

N/A Viton®

Body Material

N/A Naval Brass

Valve Size

N/A 1/4 in

Connections (Inlet)

N/A Male pipe

Certification

N/A ASME

Operating Pressure

N/A 15 to 150 psig1 to 10 bar

Operating Temperature

N/A -20 to 350 ºF

Set Pressure

N/A 15 to 150 psig

Dim. A

N/A 1.1875 in

B Hex

N/A 5/8 in

C Dia.

N/A 0.90 in

Optional Variation

N/A Manual Override

Weight

N/A .08 lbs

Shipping Weight

N/A .08 Pound

Terminology for ASME Safety Relief Valves

N/A Safety Relief Valves
An automatic pressure relieving device actuated by the static pressure upstream of the valve, which opens in proportion to the increase over the opening pressure.

Start-to-Leak Pressure
The pressure at the valve inlet where the relieved fluid is first detected (on the downstream side of the seat) before normal relieving action takes place

Opening Pressure (Set Pressure)
The valve inlet pop point pressure at which there is a measurable lift or discharge becomes continuous as determined by seeing, hearing or feeling. In the pop type of safety valve, it is the inlet pressure at which the valve opens, allowing a larger amount of fluid as compared with corresponding valve movements at higher or lower pressures

Note: A safety relief valve is not considered to open when it is simmering at a pressure just below the popping point even though the simmering may be audible. This set pressure distinguishes our ASME relief valves from our standard relief valves whose cracking pressure indicates initial flow.

Relieving Pressure
(Opening pressure plus overpressure) The pressure measured at the valve inlet at which the relieving capacity is determined.

Closing Pressure
(Reseat pressure) The pressure measured at the valve inlet, at which the valve closes, flow is substantially shut off , and there is no measurable lift.

Seal-off Pressure
The pressure (measured at the valve inlet) after closing at which no further gas is detected at the downstream side of the seat.

Operating Pressure
The actual pressure at which a vessel is maintained in normal operation.

Accumulation
Pressure buildup or overpressure beyond the set pressure of a safety relief valve, at which capacity flow is rated. Capacities are usually based on 10% accumulation.

Recommended Installation

N/A

  1. Before installing a new safety relief valve, we recommend that a pipe tap be used to assure clean-cut and uniform threads in the vessel opening and to allow for normal hand engagement followed by a half to one turn by wrench.
  2. Avoid over-tightening as this can distort the valve seat.
  3. Avoid excess “popping” of the valve. Safety relief valves should only be operated often enough to assure they are in good working order.
  4. Apply only a moderate amount of pipe compound or tape to the threads, leaving the first thread clean parts.
  5. Don’t oversize the valve, as this may cause chatter resulting in rapid wear of the moving parts.
  6. Avoid wire, cable, or chain pulls for attachments to levers that do not allow a vertical pull. The weight of these devices should not be applied to the safety relief valve.
  7. Avoid having the operation pressure too near the valve set pressure. A minimum differential of 10% is recommended.

Safety

N/A For Your Safety
It is solely the responsibility of the system designer and user to select products suitable for their specific application requirements and to ensure proper installation, operation, and maintenance of these products. Material compatibility, product ratings and application details should be considered in the selection. Improper selection or use of products described herein can cause personal injury or property damage.




307 Derstine Ave, Suite 204 | Lansdale, PA 19446 | Phone: 267-933-6300 | Fax: 267-933-6305 | Toll Free: 800-645-6733 | Email: [email protected]
Terms & Conditions | Catalog Index | © 2009- Circle Valve Technologies, Inc. All Rights Reserved