[email protected]
800-645-6733
Home About Us Line Card Careers Products Contact Us
[email protected] 800-645-6733
Home
About Us
Products
Line Card
Careers
Blog
Contact Us
Features
  • M5100 Series offered with ring or lift handle
  • MD500 Series features cup design with manual override ring
  • Zero leakage from 0 psi up to 70% of the marked set pressure
Please specify ‘ASME’ when placing your order.
Unit of Measure

Specifications

Series

N/A M5100

Handle Type

N/A Lift Handle

Certification

N/A ASME

Body Material

N/A Naval Brass

O-Ring Material

N/A Buna N

Set Pressure

N/A 50 to 1200 psig

Valve Size

N/A 1/2 in

Connections (Inlet)

N/A Male pipe, Lock Wire

Operating Pressure

N/A 50 to 1200 psig3 to 83 bar

Operating Temperature

N/A -40 to 250 ºF

Dim. A

N/A 1/2 in

Dim. E

N/A 3.86 in

Dim. M

N/A 5.51 in

B. Dia.

N/A 1 1/4 in

H Hex

N/A 1.25 in

Weight

N/A .9 lbs

Terminology for ASME Safety Relief Valves

N/A Safety Relief Valves
An automatic pressure relieving device actuated by the static pressure upstream of the valve, which opens in proportion to the increase over the opening pressure.

Start-to-Leak Pressure
The pressure at the valve inlet where the relieved fluid is first detected (on the downstream side of the seat) before normal relieving action takes place

Opening Pressure (Set Pressure)
The valve inlet pop point pressure at which there is a measurable lift or discharge becomes continuous as determined by seeing, hearing or feeling. In the pop type of safety valve, it is the inlet pressure at which the valve opens, allowing a larger amount of fluid as compared with corresponding valve movements at higher or lower pressures

Note: A safety relief valve is not considered to open when it is simmering at a pressure just below the popping point even though the simmering may be audible. This set pressure distinguishes our ASME relief valves from our standard relief valves whose cracking pressure indicates initial flow.

Relieving Pressure
(Opening pressure plus overpressure) The pressure measured at the valve inlet at which the relieving capacity is determined.

Closing Pressure
(Reseat pressure) The pressure measured at the valve inlet, at which the valve closes, flow is substantially shut off , and there is no measurable lift.

Seal-off Pressure
The pressure (measured at the valve inlet) after closing at which no further gas is detected at the downstream side of the seat.

Operating Pressure
The actual pressure at which a vessel is maintained in normal operation.

Accumulation
Pressure buildup or overpressure beyond the set pressure of a safety relief valve, at which capacity flow is rated. Capacities are usually based on 10% accumulation.

Safety

N/A For Your Safety
It is solely the responsibility of the system designer and user to select products suitable for their specific application requirements and to ensure proper installation, operation, and maintenance of these products. Material compatibility, product ratings and application details should be considered in the selection. Improper selection or use of products described herein can cause personal injury or property damage.



Check Valves
Relief Valves
Vacuum & High Purity Fittings
Circle Seal Solenoid Valves
Jefferson Solenoid Valves
Atkomatic Solenoid Valves
GO Regulator
Cryogenic Valves & Equipment
Hoke Valves
Gyrolok® Tube Fittings
Circle Seal Control Valves
Measurement Devices
Additional Products



1533 Gehman Road | Harleysville, PA 19438 | Phone: 267-933-6300 | Fax: 267-933-6305 | Toll Free: 800-645-6733 | Email: [email protected]
Terms & Conditions | Catalog Index | © 2009- Circle Valve Technologies, Inc. All Rights Reserved